Re: issue with axis rotation in animation
These videos are based on the previous post. I disabled the separate sketch-locked assembly constraint so it would recognize the pin connection. Using a snapshot for the analysis, I was able to get...
View ArticleRe: Windchill DTI Install/Run Issue
OK so we've done quite a bit more digging on this issue and it seems to be the installer runs ok but using the configuration does not populate the registry properly.After a fresh install the registry...
View ArticleRe: Units issue
multiply the LHS of your equation by (mL bar)/(N m), leave the 20, it'll come out right.
View ArticleClik here to view.
Feature Failure with Repeating Patterns
Just recently I transfered from one division of my company to another. The first division used SolidWorks and the new division uses Creo. It has been over a decade since I used Pro/E so I am...
View ArticleClik here to view.
Re: Units issue
Fred Kohlhepp wrote: multiply the LHS of your equation by (mL bar)/(N m),Isn't it the other way round? Basically thats what Richard suggested. @Ben: You wanted Mathcad to show its correction factor,...
View ArticleRe: Feature Failure with Repeating Patterns
The typical response from customer support for such attempts is to group the features before patterning. I might also suggest you make sure you are on Creo 2.0 release M090. There were some serious...
View ArticleRe: help on copy paste options in creo 2.0
Ok, I found a solution to get the copy and paste work like it used to. You have to set a hidden config.pro option.This came from the PTC help tickets. Set hidden config.pro option...
View ArticleRe: project tool in sketch, there has to be a better way!
Honestly, unless you just expect the spoftware (ANY) software, to just do it for you automatically, I don't see an issue here. Copying a loop is quick, painless, and simple. What's the problem?
View ArticleClik here to view.
Re: Create a networke in Cabling Extension
Hi David... Go to File->Options->Assembly and check to make sure you do not have restrictions on so-called "out of scope" references. There's an option in assembly mode to prevent you from making...
View ArticleTry changing Num Digits under Sec Environ.
Working in Creo 2.0 Sheet Metal and I'm trying to add a dimension and I'm getting the following message "Could not add selected dimension. Try changing Num Digits under Sec Environ." How do you change...
View ArticleClik here to view.
Re: Try changing Num Digits under Sec Environ.
There is no "environment" in Creo. It is actually in options under "sketcher".
View ArticleEdit Attributes on Multiple Documents - checkin with same file PDM 9.1
I have multiple documents I'm trying to edit attributes. When I select them in the library, I choose Edit>Edit Multiple Objects. I can change the attribute value in the table. I changed my table...
View ArticleRe: Units issue
I understand your point, but I'd suggest it's only wrong because at the point the equation is defined Mathcad knows the input units but not the output units. If all units are known, either by defining...
View ArticleRe: Units issue
Many of the equations in the (old) engineering texts (Mark's Handbook, Machinery's Handbook) give equations with numerical constants that are merely unit conversion factors. (Ever see 1.414, 0.707, or...
View ArticleXY plotting is sin-function
Hello I'm new in Mathcad and having a stupid issue regarding sin-function X-Y plotting and x/y-axis unit labbeling. In attached file defining angular speed unit as rad/s, no plotting of ik(t) as...
View ArticleRe: Query Builder - State promotion date
State changes are shown as "Maturity History for each object on it's info pages and available Query Builder as Life Cycle History type, with the timestamp when the object reached a certain state as the...
View ArticleRe: XY plotting is sin-function
In attached file defining angular speed unit as rad/s, no plotting of ik(t) as obtained.Deleting the angular speed unit definition, plot is OK.Why? What do I miss?You are trying to do a so called...
View ArticleRe: Units issue
Put in the correct equation (i.e. 2*pi). If you put in 20*pi all you are doing is propagating an outdated methodology. As suggested, add a note next to it explaining why it differs to the literature...
View ArticleRe: Creo 2.0 and 3D connexion mouse
I don't find that. Where I need to do that in Creo or in mouse software?
View Article