Re: I am getting 2 emails now for every post. I figure I am following one to...
ryankelley, How do I see everything or everyone I am following? I don't think I am following any specific people so I figure I have somehow double followed somewhere.
View ArticleRe: Global Position Annotation
You can export to IGES based on a coordinate system. IGES will have the 3D location for each point and is formatted as an ASCII text file. You can extract that data for analysis in Excel or other...
View ArticleClik here to view.
Re: I am getting 2 emails now for every post. I figure I am following one to...
Well, I figured out what I was following. I went to BROWSE, COMMUNITES, the selected FOLLOWING.I am only following CREO so I still don't know why I am doubled up on community emails.
View ArticleClik here to view.
Re: Trouble with Syntax Highlighting in Advanced Editor
Ryan,Here are 2 videos. I am running Windows 7 Pro 64-bit SP1. One video is IE9. The other video is Chrome39. Curiously, I wasn't able to reproduce the issue with double letters. If I were to...
View ArticleRe: Creo 2 M120 Learning connector button not working
WayneBeck, I'm running Creo 2.0 M130 and using dual monitors. When I click Learning Connector, it pops up on the second monitor (not the one Creo is displayed on). I've had it where I am running on a...
View ArticleCan I pull parameter information out of a NX part and populate a Windchill...
My ultimate goal here is to customize the default Windchill BOM. In doing this I want to take information out of my parts and populate the new columns in the BOM. Can this be done even with CREO parts?...
View ArticleClik here to view.
Re: I am getting 2 emails now for every post. I figure I am following one to...
Good, that helps isolate the types of email updates you're receiving. Two follow up questions: Are you following the Creo community in your Inbox?Have you enabled email updates within your connections...
View ArticleClik here to view.
Clipped Axis
How do I take the breaks/clippings out of an axis that has been cut/clipped in a drawing in Creo 2.0?
View ArticleAdding Signoffs in a Workflow
I have an existing worklflow that we need to modify to add signature signoffs at the end before the workflow is completed. I haven't modified a workflow since Windchill 7 and this workflow was created...
View ArticleClik here to view.
Re: tolerances in drawing
All, tol1.jpg from Demac was as: I don't think directly you can get this, however as an alternate option you can try using Plus-Minus tolerance mode and set lower tolerance to 0.0. After that blank...
View ArticleRe: Influencing Curves
John, Read the attached pdf, and it will give you a better understanding on how to use influencing curves.
View ArticleRe: Hidden Lines Extrude Error
Wade, If I am not wrong there were some issues similar as yours which were corrected in latest datecodes of Creo 2.0. You may try installing latest version of Creo 2.0
View ArticleRe: tolerances in drawing
thanks for reply but i did not find blank_zero_tolerance in drawing options ( i'm using creo 2)
View Articlelack of precision in Creo Elements / Direct Modeling Express?
Hi Folks, I am using Creo Elements / Direct Modeling Express. I like it a lot in some ways. But I find that I am spending quite a bit of time repeatedly fixing things that seem out of place or not...
View ArticleClik here to view.
Re: tolerances in drawing
I'm in Creo 2 also. It's there under the tolerances section in the drawing setup. (not config.pro) FILE, PREPARE, DRAWING PROPERTIES, change (across from detail options)
View ArticleShell tool failure
I drew a bottle by starting with a rectangle and then did a circle to square sweep. The top circle was then extruded and the bottom square also extruded. I select the top and shell but Creo fails to...
View ArticleClik here to view.
Re: tolerances in drawing
Yes, it is an old drawing option available in Creo 2.0 as well. Make sure your are checking this in drawing options not in config options (File > Prepare > Drawing Properties > Detail options...
View ArticleRe: How can you Message people who are not your Friends/Followers
Ha, me too! I've never used twitter either.
View ArticleClik here to view.
Re: PTC Creo All Content sorted by recent activity vs PTC Creo Overview
The "Recent Content" widget on the Creo Overview page displays item activity from both the parent product community and nested sub-communities ( Modeling, Visualize, Analysis and Simulation, etc.) to...
View Article